收藏本站
NMT Series
Triple Output 3W DC/DC Converters
APPLICATION NOTES
RIPPLE SPECIFICATION
The output ripple for the NMT series is higher than standard for a Murata Power Solutions DC/DC converter.
This is due to using low value ceramic capacitors internally for longer life perfomance of the component and
the superimposition of ripples between each output channel. Consequently with a maximum 400mV ripple per
output channel, at -72V the ripple is potentially three times this value (1.2V). The ripple will always be additively
superimposed since the output windings are synchronized.
To reduce ripple, external capacitors are recommended with a value of 1μF per channel (see ?gure 1). This
typically reduces the ripple to 50mV per channel. Further ripple reduction can be achieved by use of series
inductors on each output channel plus additional external capacitors to form a pi-?lter with the internal capaci-
tors of the device.
SLIC CIRCUITS
T he primary application for the NMT series is in subscriber line interface circuits (SLIC’s), particularly for the
Integrated Services Digital Network (ISDN). The NMT can also be used in standard telecommunications circuits
where a local power source is preferred to the telephone system power due to either the power quality of the
telecommunications system power supply or to avoid potential power line disturbances, such as lightening
strikes and access switching, which will effect the target circuit function.
Another application area is in ?bre-in-the-loop (FITL) or radio-in-the-loop (RITL) interfacing via a standard tele-
communication SLIC, where the usual telecommunication battery voltage is not available due to the transmis-
sion media in use (?bre or radio). In particular, FITL/RITL interfaces directly on PC cards, in local monitor and
boost circuits and at exchanges between the ?bre/radio and wire media.
The supply rails can be used for ringing generators as well as SLIC circuits or where both are combined, such as
in the AMD AM79R79 Ringing SLIC device (see ?gure 2). The -72V rail is used primarily for the generation of the
ringing signal (V BAT 1), the -48V rail is used to supply in line access circuitry (V BAT 2) and the -24V supply for the
Figure 1. V OUT3 Output Ripple
Top: No external capacitors
Bottom: 1μF per channel external capacitors
Figure 2. Supply for Ringing SLIC Device
on-chip regulator for the logic interface (V NEG ). Alternative devices from other manufacturers could use the -24V
output for their internal circuit supply and -72V for ringing.
TECHNICAL NOTES
ISOLATION VOLTAGE
‘Hi Pot Test’, ‘Flash Tested’, ‘Withstand Voltage’, ‘Proof Voltage’, ‘Dielectric Withstand Voltage’ & ‘Isolation Test Voltage’ are all terms that relate to the same thing, a test voltage,
applied for a speci?ed time, across a component designed to provide electrical isolation, to verify the integrity of that isolation.
Murata Power Solutions NMT series of DC/DC converters are all 100% production tested at their stated isolation voltage. This is 1kVDC for 1 second.
A question commonly asked is, “What is the continuous voltage that can be applied across the part in normal operation?”
For a part holding no speci?c agency approvals, such as the NMT series, both input and output should normally be maintained within SELV limits i.e. less than 42.4V peak, or
60VDC. The isolation test voltage represents a measure of immunity to transient voltages and the part should never be used as an element of a safety isolation system. The part
could be expected to function correctly with several hundred volts offset applied continuously across the isolation barrier; but then the circuitry on both sides of the barrier must
be regarded as operating at an unsafe voltage and further isolation/insulation systems must form a barrier between these circuits and any user-accessible circuitry according to
safety standard requirements.
REPEATED HIGH-VOLTAGE ISOLATION TESTING
It is well known that repeated high-voltage isolation testing of a barrier component can actually degrade isolation capability, to a lesser or greater degree depending on materials,
construction and environment. The NMT series has toroidal isolation transformers, with no additional insulation between primary and secondary windings of enameled wire. While
parts can be expected to withstand several times the stated test voltage, the isolation capability does depend on the wire insulation. Any material, including this enamel (typically
polyurethane) is susceptible to eventual chemical degradation when subject to very high applied voltages thus implying that the number of tests should be strictly limited. We
therefore strongly advise against repeated high voltage isolation testing, but if it is absolutely required, that the voltage be reduced by 20% from speci?ed test voltage.
This consideration equally applies to agency recognized parts rated for better than functional isolation where the wire enamel insulation is always supplemented by a further
insulation system of physical spacing or barriers.
www.murata-ps.com/support
KDC_NMT.E04 Page 3 of 4
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
NMV1515SAC CONV DC/DC 1W 15VIN 15VOUT SIP
NMV2415SC CONV DC/DC 1W 24VIN 15VOUT SIP
NMXD0515UC CONV DC/DC 5W 5VIN 15V DIP UNREG
NMXS1205SOC CONV DC/DC 5W 12VIN 5V DIP REG
NOJE687M004RWJ CAP NIOB OXIDE 680UF 4V 2917
NOJX686M006RWJ CAP NIOB OXIDE 68UF 6.3V 2917
NOME687M002R0023 CAP NIOB OXIDE 680UF 2.5V 2917
NOSV108M002R0050 CAP NIOB OXIDE 1000UF 2.5V 2924
相关代理商/技术参数
NMT0572SC 制造商:Murata Power Solutions 功能描述:DC-DC CONVERTER
NMT0572SZ 功能描述:DC/DC转换器 3W TRIPLE OUTPUT RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:
NMT0572SZC 功能描述:DC/DC转换器 3W 5Vin W/Shutdownpn TripOut -24,-48,-72V RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:
NMT-1 功能描述:烙铁 FCR Nozzle Maint Tool RoHS:否 制造商:Weller 产品:Soldering Stations 类型:Digital, Iron, Stand, Cleaner 瓦特:50 W 最大温度:+ 850 F 电缆类型:US Cord Included
NMT1272S 功能描述:DC/DC转换器 USE 580-NMT1272SC RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:
NMT1272SC 功能描述:DC/DC转换器 12V to -24V 42mA 3W Triple Output RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:
NMT1272SC 制造商:Murata Power Solutions 功能描述:DC-DC CONVERTER
NMT1272SZ 功能描述:DC/DC转换器 3W TRIPLE OUTPUT RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: